Skip to main content

Full text of "Woodworking"

See other formats

Wooden Buttons 


Make Projects 

build, hack, tweak, share, discover, J 

Wooden Buttons 

Written By: Kristin Roach 


Drill (1) 

Jigsaw (1) 

or coping saw and vise or C-clamps 


Sandpaper (1) 

t> PARTS: 

• Branch (1) 

• Beeswax (1) 


After a big windstorm, it can be a little overwhelming to look at all the branches and sticks 
that need to be picked up in the yard. Instead of dreading this cleanup task, you can see it 
as a chance to collect all sorts of great materials for creative projects. 

For example: I really like wooden buttons, but the ones from stores are often so highly 
polished that they barely look like wood at all. Here's how to make nicer ones out of fallen 
branches that you find yourself. These buttons are smooth, but they retain the beautiful 
characteristics of the tree they came from — grain, texture, and even bark, if you choose. 
They are the perfect thing to adorn your totes, shirts, bags, or any other project that needs a 
little tree bling! 

© Make Projects 

Page 1 of 4 

Wooden Buttons 

Find a hardwood branch with a straight section 6"-8" long by 3 /4 n -1 1 /2" wide. You can use a 
fallen branch or cut one yourself, but make sure it has no sticky sap and a small pith (the 
hollow or spongy center), no more than 1/8" for a 1"-wide branch. 

Moisture level is important. Branches that are too dry will snap when bent, and 
freshly fallen or cut branches will need to dry out in the sun for a day or two before 
being made into buttons. Buttons cut from wood that's too green or wet will crack once 
they dry all the way. Expect some trial and error with determining the right moisture. 

You can leave the bark on your buttons, but if you want to remove it, use a sharp knife to 
peel away 2"-3" of bark at one end of the branch, working around it evenly with shallow 
strokes. It's important that your knife is really sharp; if it's dull, removing the bark isn't just 
a pain — you're also more likely to slip and cut yourself. 

Place the branch in a vise and use the 1/16" bit to drill 2 or 4 evenly spaced holes into the 
cut center of the branch. Keep the drill level with the branch, or your holes will be skewed, 
and don't drill too close to the perimeter of the branch, or you may break through it. 

Use a jigsaw or coping saw to cut 1/8"-wide circular slices from the branch. 

© Make Projects 

Page 2 of 4 

Wooden Buttons 



Next you'll need to clean the wood pulp out of the holes and widen them. Hold the 5/64" bit 
in your hand and gently turn it through all the buttonholes to widen them. Repeat with the 

3/32" bit. 

You may want to use a bit of cloth for grasping the drill bit or you could hurt your 
fingers over the course of making a half-dozen buttons — as I did the first time. 


Sand the buttons, starting with the 220-grit sandpaper and working through to the finest 
grit. Depending on how rough you want your buttons, you can do just a few strokes or work 
all the way up to 600-grit sandpaper to make them really smooth. If you want to finish the 
buttons with a natural seal, rub on a little beeswax then wipe off the residue with a clean 

Try out a few different ways of sanding and finish- ing with individual buttons. Once you 
find a finish you like, go crazy and make a whole set that way! 

© Make Projects 

Page 3 of 4 

Wooden Buttons 

This project first appeared in MAKE Volume 24 . page 126. 

This document was last generated on 201 2-1 1 -03 02:53:1 4 AM. 

© Make Projects Page 4 of 4